Download
data sheet |
Short description |
Product image |
Lamp tester LT1 |
The LT1 is suitable for the testing of gas-filled UV lamps. When the lamp contacts are touched with the probe tip, the gas inside the lamp is ionised and the lampgas glows blue, indicticating a healthy lamp. |
|
UV Spectro NEW |
UV Spectro
Spectral range: 200 – 440 nm
Spectral bandwidth: 2 nm
Irradiance range: 2 - 5,000 (25 - 35,000) mW/cm²
Irradiance dose range: 1 (25) mJ/cm² 600 (42,000) J/cm²
Measurement time: 0 to 120 s
Sampling Rate: 10 ms – 1,000 ms
Cosinus correction: yes
Display: LCD, 128 x 64 ppi
Operating temperature: 70 °C
Weight: 375 g
Delivery: UV Spectro, plastic case, 3 x coin cell CR 2032, manual, calibration certificate. |
|
UV Control 3C
UV Control 3CT |
Integrator for measuring UV intensity
and dose plus temperature
+ UV-A intensity mW + UV-A dose mJ
+ UV-B intensity mW + UV-B dose mJ
+ UV-C intensity mW + UV-C dose mJ
+ UV-VIS intensity mW + UV-C dose mJ
(UV Control 4C/4CT)
+ Full UV intensity mW + Full UV dose mJ
+ Temperature °C / °F (UV Control 3CT/4CT) |
|
UV Control 4C
UV Control 4CT NEW |
Integrator for measuring UV intensity
and dose plus temperature
+ UV-A intensity mW + UV-A dose mJ
+ UV-B intensity mW + UV-B dose mJ
+ UV-C intensity mW + UV-C dose mJ
+ UV-VIS intensity mW + UV-C dose mJ
(UV Control 4C/4CT)
+ Full UV intensity mW + Full UV dose mJ
+ Temperature °C / °F (UV Control 3CT/4CT) |
|
UV Control 4CT LED
NEW |
UV Control 4CT LED
Same as UV Control 3CT but for
measuring in four UV bandwidths
UV-A: 315 – 410 nm
UV-B: 280 – 315 nm
UV-C: 230 – 280 nm
UV-VIS: 395 – 445 nm
4CT LED: 265 – 495 nm |
|
UV Disc |
Integrator with integrated heat shield
for measuring the UV dose
This measuring instrument measures the applied dose thereby examining the effects of UV lamp aging and contamination. It can be used where a conveyor belt (or similar) passes underneath uv lamps, e.g. in UV-curing ovens, photo-resist
exposure systems, printed board exposure systems etc. which is typical in the furniture and printing industry, as well |
|
UV Micro Puck
|
The UV Micro Puck is a high-end UV measurement system intended to measure the UV dose at locations that are difficult to access. The standard version of the UV Micro Puck Integrator includes a UV sensor for measuring UV wavelengths from 230 to 410 nm. |
|
Handheld HI 1
|
Hand-held display unit HI 1 for the new UV sensor SI 1 with intelligent interface connector (sensor connector). Easy to handle display unit, large 7/16 segment display with dimension indication, storage of maximum and minimum measured values, hold function, range monitoring and sensor break detection. |
|
UV Sensor SI 1 |
The UV sensor SI 1 is a robust measuring cell that is used in combination with the hand-held HI 1 for short-period UV measurements, even in harsh ambient conditions and at high temperatures. The sensor is available for various UV ranges. The calibration data of the sensor is stored in the sensor connector. |
|
UVM-QSO 3
|
UV on-line sensor for continuous performance monitoring of UV lamps. Due to its robust design with a beam injection window made of quartz glass within a tube of stainless steel, this sensor can also be exposed to high radiation continuously. The sensor emits an output signal of 0 … 10 VDC which is proportional to the incident UV radiation. The integrated purging air connection can be used to keep the quartz glass rod clean in contaminated ambient air. |
|
PM41-UVT
|
PM41-UVT measures infrared radiation in the range between approx. 4.5 and 4.8 µm. In this way, the sensor only records the long-wave radiation of the quartz and therefore measures the actual temperature of the quartz tube. The sensor targets the lamp from a distance of approx. 4 to 10 cm with a measuring spot of 3.8 to 13 mm in diameter. |
|
